DTA installation on c20let

Diskutiere DTA installation on c20let im International Corner Forum im Bereich Technik; Hi @all I am installing a P8PRO DTA system on my c20let engine. (www.dtafast.co.uk) It's a very nice system with launch/traction control and...
G

GSI-TURBO

Dabei seit
21.09.2001
Beiträge
104
Punkte Reaktionen
0
Hi @all

I am installing a P8PRO DTA system on my c20let engine.
(www.dtafast.co.uk)
It's a very nice system with launch/traction control and a.l.s

But now i got a question, how many degrees ignition can i run maximum on 1 bar boost ?

I also can make a map for atmospheric ignition degrees and make a pressure compensation... but how many % or degree retard do i need when raising 0,1 bar ???

The same applies to the air inlet temperature. how many % retard is needed at 10degree celcius raise ?

I want to keep the engine alive .. so thats why i ask these basic ignition facts..

Regards,

Dennis
 
J

Joe

Dabei seit
23.09.2001
Beiträge
640
Punkte Reaktionen
0
Ort
Universum, Milchstrasse, Sonnensystem, irgendwo au
Dennis,

as I couldn't find any information on the referenced website about supporting a knock sensor, I assume that its in fact not supported.

I guess this means that you need a good and well tested program for this engine managment system made for the C20LET engine or you are forced to put your engine with the new EMS onto a test stand and you there have to find out which ignition angle is still ok under which conditions.

That's why I never would buy an EMS which doesn't support a knock sensor and an EGT-sensor. Autronic has a system that supports both and is even able to learn by driving. That means the EMS needs some start params after installation and then you can drive carefully and while you drive the system learns how your engine wants to be treated. But , sadly, as always , its not inexpensive !
 
ASH

ASH

Dabei seit
20.09.2001
Beiträge
1.870
Punkte Reaktionen
1
Hi !

Also please please please dont kill our best working K26 Hybrid turbocharger during the optimisation or trial !

Its very easy to overtemperature the charger at the exhaust side , only some bits were left , when you ust wrong exhaust temp !°

regards ASH
 
G

GSI-TURBO

Dabei seit
21.09.2001
Beiträge
104
Punkte Reaktionen
0
Arno,

I installed an Exhaust Temperature Gauge, and i will just a small amount of ignition retard, and a small ammount of fuel during A.L.S testing.

But first the car must run, and then i will install the rest of the system like traction control and launch control..
 
Thema:

DTA installation on c20let

DTA installation on c20let - Ähnliche Themen

A14NEL and F17 remap: I have a combination of A14NEL engine and F17 gearbox in Meriva B. EDS offers a remap that would get about 165HP and 265Nm. The team from EDS says...
It is imperative that you do follow all the safety: Riding a skateboard always has some risk associated with it. However, you can do your part to be responsible and to have fun with it at the same...
like cocktail parties, wedding anniversaries, weddings or: Pandora Jewelry Charms Are usually correct way to measure your current wrist bracelet Pandora? Undoubtedly, the easiest way to get fitted to get a...
adidas neo lite racer mens: Beam Prohibit adidas neo uk Shades Purchase in the intro of the United states Atmosphere Pressure Lieutenant difficulty. within 1930, Bausch as...
Why is my engine retarding ignition?: Hi guys, please help me with my Zafira OPC Z20LEH. Why is my engine retarding ignition? I have always felt i was missing top end power so i...
Oben